Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
See the difference
Before
After
Before
After
Before
AfterHow Much Does a Chimney Cap and Crown Cost in Boca Raton?
Chimney cap and crown work in Boca Raton typically runs $175 to $850 for a cap installed on a standard flue, and $450 to $1,400 when a crown repair is added to the same visit. A damaged crown that needs rebuilding rather than patching usually lands between $500 and $1,600 depending on the size of the chimney top and how far the cracking reaches.
Those figures are estimates for the Boca Raton market. The written estimate we give you after looking at your chimney sets the final price, and it’s free.
Key Takeaways
- A single standard cap usually costs $175 to $450, including installation.
- Crown repair with a sealant or coating typically runs $450 to $900.
- A full crown rebuild is the biggest line item, usually $500 to $1,600.
- Doing cap and crown together saves money versus booking two visits.
- We work with Gelco, Famco, Olympia Chimney, and Copperfield products, so the cap on your chimney matches the flue it protects.
Chimney Cap and Crown Cost Breakdown (2026)
The top of a chimney has two separate jobs: the cap keeps water, animals, and sparks out of the flue, and the crown sheds rain away from the masonry below it. They fail in different ways, so they price out differently. Here’s what each piece typically costs in Boca Raton.
| Work | Typical Cost Range | What’s Included |
|---|---|---|
| Single-flue cap, standard galvanized | $175 – $350 | Cap, mounting, sealing, fit check |
| Single-flue cap, stainless | $250 – $450 | Cap, mounting, sealing, fit check |
| Multi-flue cap (custom-fit) | $350 – $850 | Measured cap, mounting, full seal |
| Crown repair (sealant or coating) | $450 – $900 | Prep cracks, apply coating, allow to cure |
| Crown rebuild (partial or full) | $500 – $1,600 | Remove damaged crown, re-form, slope and seal |
| Crown rebuild with flue tile repair | $900 – $2,200 | Crown plus HeatShield work on the top flue tile |
| Cap and crown in a single visit | $450 – $1,400 | Both jobs, one set-up, one travel |
The spread inside each line comes down to a few things. Access matters most. A chimney with a walkable roof and clear surroundings takes less time to reach than one tucked behind a screen enclosure or a steep pitch. Cap size is the second driver; a cap custom-fitted to a multi-flue chimney costs more than an off-the-shelf unit for a single round flue. The material of the cap matters too, since stainless holds up far better than galvanized over time. And if the crown has already pulled away from the flue, the repair grows to include rebuilding the slope so the water actually runs off instead of pooling. All of these are checked during an inspection before anything gets priced, and the estimate you receive reflects what’s actually on your roof.
What Affects Chimney Cap and Crown Pricing in Boca Raton
Boca Raton doesn’t have the freeze-thaw problem that wrecks masonry in colder parts of the country. What it does have is a long rainy season and a humid climate, and both wear on crowns and caps in ways homeowners don’t always expect. Here are the things that move the price.
- Chimney top condition. A hairline crack in the crown means a coating job. A crown that’s crumbling, separated from the flue, or leaning needs a rebuild, and that’s the difference between a repair and a much larger line item on the estimate.
- Number of flues. Homes with a fireplace plus a second flue for a stove or furnace need a multi-flue cap. Those are custom-sized to the chimney’s footprint, so they sit higher in the price range than a single-flue unit.
- Roof access and pitch. A steep pitch, a slick tile roof, or a chimney screened by landscaping adds setup time. That’s part of what a proper site assessment uncovers before we quote, not after.
- Cap material. Stainless steel resists rust and holds its finish in South Florida’s humidity, so it usually costs more up front than galvanized and lasts longer. That’s a case where the higher number often wins over time.
- Flue tile damage found during the job. Sometimes the top flue tile is spalled or cracked right where the crown meets it. That’s fixable with HeatShield resurfacing of the top section, which costs far less than tearing out a liner.
- Crown area and shape. A large, square crown over a wide chimney takes more material and labor to re-form correctly than a small, round one.
One factor worth mentioning separately: an inspection almost always turns up more than a crown problem. The same visit that prices a cap often reveals a flue that needs attention, and we’ll tell you exactly what we found, then let you decide what to fix now and what can wait. That inspection is part of how we handle chimney sweep Boca Raton work, since the sweep and the check-up happen together.
Cap and Crown: Why They Go Together
A cap without a sound crown is a partial fix. The crown is the masonry slab at the very top that angles water away from the flue, and the cap is the metal or mesh cover that sits above it. When a crown cracks, rain gets into the masonry and the flue, and if a cap is missing or damaged, the crown takes the full force of the weather along with everything else. That’s why we often quote both at once, and why the combined line in the table usually comes in lower than two separate visits.
The materials matter here, and they’re where a specialist differs from a generalist. We work with Gelco and Famco cap and venting products because they fit standard flue sizes correctly and hold up. A cap that’s the wrong size lets rain blow in sideways, and a cap that’s cosmetic-only will rust or bend within a couple of seasons. On the crown side, we work with HeatShield resurfacing when the damage extends into the flue tile, because HeatShield lets us restore the tile rather than rebuild the whole top.
Because we handle sweeping, inspection, and repair under one service relationship, there’s no gap where the sweeping company and the repair company each claim the other caused the problem. It’s one report, one estimate, one set of hands on the roof.
How to Save on Chimney Cap and Crown Work in Boca Raton
The best savings come from timing, not haggling. A crown that’s caught while it’s still a hairline crack costs far less to fix than one that’s crumbled and pulled away. Here’s what actually helps.
- Book the cap and crown together. A combined visit shares the set-up and roof access, so it’s typically less than two appointments.
- Fix cracks while they’re small. Crown sealant applied early costs a fraction of a rebuild later. If you can slide a dollar bill into a crack, it’s time to call.
- Choose stainless over galvanized. The up-front difference is modest and stainless holds up much longer in this climate, so you’re less likely to pay for the job twice.
- Get the inspection first. Knowing exactly what needs fixing, and what doesn’t, keeps you from paying for repairs you don’t need. Our inspection is structured to report specific findings, not to sell.
- Ask about HeatShield on the top flue tile. If tile damage is found where the crown meets the flue, resurfacing costs far less than a liner replacement.
We give free estimates, and the written estimate you receive sets the final price with no surprises. Call (877) 685-2248 to book a look at your chimney top. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Is a Cap and Crown Repair Worth It in Boca Raton?
Yes, and the reason isn’t cosmetic. A cracked crown lets water into the masonry, and once it’s in, the flue tile below can crack and open a path for smoke and carbon monoxide to reach places it shouldn’t. A missing cap lets rain run straight down the flue and gives birds, squirrels, and wasps a way in. Spending a few hundred dollars to close those paths is far cheaper than the water damage, liner repair, or rebuild that results when they’re left alone through another rainy season.
It also protects the rest of your chimney system. Everything below the crown, from the flue tiles down to the firebox, depends on the top staying sealed. When we visit for a Boca Raton chimney inspection, the top of the chimney is one of the first things we look at, because it tells us a lot about the condition of everything underneath. Our technicians have up to 14 years of experience reading exactly that kind of wear.
FAQs – Chimney Cap and Crown Cost
How much does a chimney cap cost in Boca Raton?
A chimney cap in Boca Raton typically costs $175 to $850 installed, with most single-flue homes landing between $175 and $450. Multi-flue and custom-fit caps sit higher in the range. Call (877) 685-2248 for a free estimate on your specific chimney.
How much does chimney crown repair cost?
Chimney crown repair usually costs $450 to $900 when the crown is cracked but solid, and $500 to $1,600 when it needs rebuilding. The written estimate after an inspection sets the final price.
Is it cheaper to repair or replace a chimney crown?
Repair is almost always cheaper when the crown is only cracked, costing $450 to $900 versus $500 to $1,600 for a rebuild. The deciding factor is whether the crown has separated from the flue or lost its slope. Below that threshold, a coating job is the better call.
Can you install a cap and fix the crown in the same visit?
Yes. We quote cap and crown together whenever the top of the chimney needs both, and the combined price of $450 to $1,400 is typically less than two separate appointments. Call (877) 685-2248 to arrange it.
Do I need a permit for chimney crown work in Boca Raton?
Most crown and cap work falls under repair rather than new construction, but permit rules vary, so it’s worth asking your city’s building department if the job involves significant rebuilding. We’ll tell you what we’ve found on your chimney and what the work involves, so you can check. Estimates are free: call (877) 685-2248.
Call for a Free Cap and Crown Estimate
If your chimney cap is bent, missing, or rusted through, or your crown has cracks that let water in, call Chimney Sweep Boca Raton at (877) 685-2248 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. We work with DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, and Copperfield products, so the cap and crown we install fit your flue and stand up to Florida humidity. We’ll tell you exactly what we found on your chimney, quote the work in writing, and let you decide.
Written by the team at Chimney Sweep Boca Raton.
Pricing reflects the Boca Raton market as of 2026. Chimney Sweep Boca Raton offers free estimates – call (877) 685-2248.
What Our Customers Say
"Creosote buildup was worse than I realized. He measured it, showed me the glazing on the flue with the camera, and was honest that we were closer to a chimney fire than I wanted to hear."
- Yolanda Coleman"Good work. The written inspection report took about a week to arrive after I asked for it, which was slower than I expected."
- Hector Martinez"Drop cloths everywhere, HEPA vac, and not a speck of soot on the carpet. I'd been dreading the mess for nothing."
- Maria Guzman